The most important thing when choosing suppliers is to build trust and a shared vision.

We provide technical support and guranteefor all customers. 

These steps will help you  complete your own project construction more professionally.



Emergency Overview
Non-toxic, non explosive and is not a fire hazard.
Dust may irritate the eyes from mechanical abrasion causing watering and redness.
Dust may cause irritation of the skin from friction but cannot be absorbed through intact skin.
Unlikely under normal conditions of use, but swallowing the dust from this product may result in irritation to the mouth and gastrointestinal tract.
Dust may cause irritation of the nose, throat, and airways, resulting in coughing and sneezing. Certain susceptible individuals
may experience wheezing (spasms of the bronchial airways) on inhaling dust during sanding or sawing operations.


Remove contact lens. Flush with running water or saline for at least 15 minutes. Seek medical attention if redness persists or if visual changes occur.
Wash with mild soap and water. Contact physician if irritation persists or later develops.
If ingested, dilute by drinking large amounts of water. Do not induce vomiting. Seek medical attention.
If unconscious, loosen tight clothing and lay the person on his / her side. Give nothing by mouth to an individual who is not alert and conscious. Seek medical attention.
Remove to fresh air. If shortness of breath or wheezing develops, seek medical attention.


Cutting Outdoors:
1.OCM Building Products recommends positioning cutting station so that wind will blow dust away from user or others in working area and allow for ample dust dissipation.
2.Use one of the following methods based on the required cutting rate and jobsite conditions. --Best
• Score and snap using carbide-tipped scoring knife or utility knife (Ability to use this method depends on thickness of OCM Board being installed.)
• Fiber cement board shears (electric or pneumatic).--Better
• Dust reducing circular saw equipped with appropriate blade and HEPA vacuum extraction. --Good (for low to moderate cutting only)
• Dust reducing circular saw with appropriate saw blade.
Always use correct tools when executing all cutting operations.

Use adequate general or local exhaust ventilation to keep airborne concentrations below the permissible exposure limit.

Respiratory Protection
Dust mask is recommended.

Eye Protection
When cutting material, dust resistant safety goggles / glasses should be worn

Skin Protection
Loose comfortable clothing should be worn. OCM Building Products recommends that direct skin contact with dust and debris be avoided when possible by wearing long sleeved shirts and long trousers, a cap or hat, and gloves.
Sanding / Drilling / Other Machining
If sanding, drilling, or other machining is conducted, OCM Building Products recommends wear a NIOSH-approved dust mask.

Important Notes
1. For maximum protection (lowest respirable dust production), OCM Building Products recommends always using "Best" level cutting methods where feasible.
2. Always use a circular saw blade that is appropriate for the specific operation being undertaken.
3. It is not recommended that a grinder or continuous rim diamond blade be used for cutting.
4. Always follow tool manufacturer's safety recommendations.


What is glass magnesium plate?
OCM plate is a new type of non combustible inorganic wallboard improved on the basis of the traditional Magnesium Oxide board, and its performance is far superior to the ordinary Magnesium Oxide board in all aspects.

Composition of glass magnesium plate
Magnesium Oxide, magnesium chloride, glass fiber cloth, perlite and other raw materials as the main raw material, through the special production process

Are there dangerous components in glass magnesium plates?
OCM is a new type of environmental protection decorative material made of 100% mineral and reclaimed water. Product features:
I don't get damp - no corrosion - Free - oil - free non-toxic organic ingredients 0- The heavy metal salt - non asbestos - free formaldehyde

OCM how to achieve a negative carbon economy model?
The magnesium plate absorbs carbon dioxide in the air, which is called carbonation. As time goes on, the carbon dioxide emissions in the air can be effectively controlled. This is tantamount to a negative carbon economy model.

What are the conventional information on OCM?
The conventional dimensions of the OCM board are 1220*2440mm, 1200*2700mm, 1200*3000mm, and thickness from 3mm to 20mm. The color is usually beige, and other colors can be obtained by adjusting recipes.

Which side of the OCM board is fireproof?
The fire test is carried out on the smooth surface of the sheet.

How about the adhesion on the surface of OCM?
The surface energy spray paint, wallpaper, stone, tile and other treatment of OCM's board. The excellent adhesive property of glass magnesium plate, the structural insulation board (SIPS) was derived, and the exterior wall insulation system and indoor partition system were formed.